FLAME-RESISTANT GARMENT USER GUIDE

This garment has been certified by UL as compliant with NFPA 2112-2018, Standard on Flame-Resistant Clothing for Protection of Industrial Personnel Against Short-Duration Thermal Exposures from Fire.

IMPORTANT USER INFORMATION

This User Guide provides critical information for the proper use, care, and maintenance of your flame-resistant (FR) garment. These instructions are designed to alert you to potential hazards and help reduce the risk of serious injury or death. Non-compliance with these instructions may result in increased risk of injury. Users must review and understand this User Guide and follow all instructions during garment use.

SAFETY INFORMATION

Protection Capabilities

FR garments are designed to provide protection during brief thermal exposures or electrical arc flash events. When worn correctly, this garment can help reduce the severity of burn injuries. However, no protective garment can completely eliminate the risk of burn injury in all circumstances.

Usage Limitations

This FR garment does not provide protection against:

Prolonged direct flame contact or sustained high heat exposure
Radiological hazards
Biological hazards
Chemical or hazardous material exposure

This garment is not designed or approved for firefighting operations or emergency response activities.

Garment Condition Requirements

The protective performance of FR garments depends on proper maintenance. Do not wear garments that are:

Soiled or contaminated with flammable substances
Torn, damaged, or showing signs of deterioration
In questionable condition

Clean garments according to the care instructions in this guide. Contact John Tillman Co. customer service if you have concerns about your garment’s condition.

Customization Guidelines

Any labels, emblems, or trim added to this FR garment must comply with NFPA 2112 requirements. Non-compliant additions may compromise garment protection during flash fire or arc flash incidents. Never cover, mark through, or remove certification labels or care instruction labels.

WARRANTY

John Tillman products are warranted against defects in manufacture only. As the use and application of these products is beyond our control, no warranty is implied or intended as to their use, handling, or the results and performance to be obtained.

PREPARING YOUR GARMENT FOR USE

Proper Sizing and Fit

Your FR garment should fit comfortably without being too tight or too loose. The garment must allow full range of motion without restriction. Consult the John Tillman Co. sizing chart when selecting your garment size to ensure proper body dimension match.

[SIZE CHART – CLICK HERE]

Storage Requirements

Store your FR garment in a cool, dry location away from:

Direct sunlight
Heat sources
Excessive moisture

Prolonged sun exposure or storage in damp conditions can permanently damage the garment and reduce its protective capabilities.

INSPECTION PROCEDURES

Inspection Schedule

Inspect your FR garment:

Upon initial receipt
Before each use
After each use
Following each cleaning

What to Check

Examine the garment for:

Material Damage – Check high-wear areas including knees, seat, crotch, cuffs, elbows, and shoulders for:

Holes or tears
Excessive wear or thinning
Burn damage or melting

Seam Integrity – Inspect critical seams including inseams, outseams, seat seams, sleeve seams, and side seams for:

Broken stitching
Separation or fraying
Loose or damaged seams

Component Condition – Check closures and hardware including buttons, snaps, shanks, zippers, and buckles for:

Missing or broken components
Proper function
Secure attachment

Action Required: Immediately remove from service any garment showing signs of damage or defects. Repair or replace damaged garments before returning to use.

WEARING YOUR FR GARMENT

Putting On (Donning)

When putting on your FR garment:

Ensure proper fit adjustments are made
Fully secure all buttons, zippers, and fasteners
Tuck in the garment to ensure complete body coverage
Verify that no skin or non-FR clothing is exposed

Removing (Doffing)

When removing your FR garment:

Unfasten all buttons, zippers, and fasteners completely
Remove carefully to avoid damaging closures or seams
Do not force removal if closures are still secured

Additional Guidelines

For comprehensive information on proper FR garment selection and use, refer to NFPA 2113, Standard on Selection, Care, Use, and Maintenance of Flame-Resistant Garments for Protection of Industrial Personnel Against Short-Duration Thermal Exposures from Fire.

CARE AND MAINTENANCE

Proper care and maintenance are essential to maintain the protective properties and service life of your FR garment.

Cleaning Requirements

When to Clean: Clean your FR garment after each use to remove:

Dirt and debris
Abrasive particles
Contaminants that may reduce protection

How to Clean: Follow the care instructions on the permanent care label sewn into each garment. Non-compliance with care label instructions may cause damage or loss of flame-resistant properties.

Repair Guidelines

Authorized Repairs: If your FR garment requires repair, contact John Tillman Co. customer service to discuss repair or replacement options.

Self-Arranged Repairs: If you choose to arrange repairs independently:

Use only qualified repair services with FR garment experience
Repair materials must meet or exceed the specifications of the original garment construction
Use only fabric and components that comply with NFPA 2112
Do not make significant alterations that may reduce protective performance

GARMENT RETIREMENT AND DISPOSAL

When to Retire

Remove garments from service when they:

Show damage that cannot be properly repaired
Fail inspection criteria
Have been contaminated beyond cleaning
Show signs of protective property degradation

Disposal

Dispose of retired FR garments in accordance with all applicable local, state, and federal regulations. Ensure disposal methods prevent unauthorized reuse of damaged garments.

For questions or assistance, contact John Tillman Co. Customer Service.